Jetman
Junior Member
Joined: August 2022
Posts: 69
|
Post by Jetman on Apr 10, 2023 20:35:40 GMT -5
Hello Jetman here, after getting the amazon junk turbo out of my mind (Thanks Racket for the push to not get it!!) I have aquired a Gt5518 Turbo! Exhaust A/R is 1.60, Intake A/R is 1.10. Intake diameter is 3.5 in exhaust diameter is 4.0 in. How much usable thrust can this turbo generate? i am hoping to mount it on a bike... Thanks!
|
|
|
|
Post by racket on Apr 10, 2023 22:46:00 GMT -5
Probably ~80 lbs if it has an 81.5mm comp inducer
|
|
dieselguy86
Veteran Member
Joined: September 2014
Posts: 186 
|
Post by dieselguy86 on Apr 13, 2023 20:42:54 GMT -5
That's a low pressure turbo off a cat 15.2L acert engine. Comp inlet is 88mm,118ex. 112/102 turbine, Boreless shaft with titanium compressor wheel. Very heavy turbo with the iron compressor housing, 94lbs I think?
|
|
Jetman
Junior Member
Joined: August 2022
Posts: 69
|
Post by Jetman on Apr 14, 2023 10:51:14 GMT -5
Yes she’s pretty heavy!! I was wondering if anybody has tried using diaphragm pumps for the oil pump? Here is one I was looking at…
|
|
|
|
Post by turbinenjoe on Apr 14, 2023 12:24:05 GMT -5
Hi,
most of the cheaps 12V ones have EPDM as diaphragm material. EPDM is not resistant to engine oil because it absorbs it and expands.
They can be used but don‘t expect them to last forever.
best regards
Matthias
|
|
|
|
Post by andym on Apr 14, 2023 12:51:18 GMT -5
|
|
|
|
Post by stoffe64 on Apr 15, 2023 4:18:20 GMT -5
|
|
|
|
Post by andym on Apr 15, 2023 16:25:14 GMT -5
yep, i have used that one and the 1/2 inch version..... worth the money..... very well made... |
|
Jetman
Junior Member
Joined: August 2022
Posts: 69
|
Post by Jetman on Jun 18, 2023 17:08:14 GMT -5
Hello! I was wondering if a 90 degree elbow right out of the turbine side will affect the thrust output?
|
|
Jetman
Junior Member
Joined: August 2022
Posts: 69
|
Post by Jetman on Jun 18, 2023 17:22:42 GMT -5
|
|
|
|
Post by racket on Jun 18, 2023 17:27:25 GMT -5
Yep , there'll be some losses, how much , don't know
|
|
Jetman
Junior Member
Joined: August 2022
Posts: 69
|
Post by Jetman on Jul 1, 2023 21:55:14 GMT -5
Hello! I am just working on some of the pressure gauges… where should I mount them?? Thanks!
|
|
|
|
Post by racket on Jul 1, 2023 22:05:33 GMT -5
Oil at turbo lube inlet
P2 comp discharge , in a quiet corner of the combustor where air speeds are low
|
|
Jetman
Junior Member
Joined: August 2022
Posts: 69
|
Post by Jetman on Jul 20, 2023 8:14:51 GMT -5
Hello! The engine is slowly coming along… I am in need of a high gph oil nozzle and can’t seem to locate one in the U.S or Canada. Any help would be much appreciated! Thanks
|
|
|
|
Post by racket on Jul 20, 2023 20:40:21 GMT -5
What sized nozzle ??
|
|
