|
Post by stoffe64 on Apr 19, 2024 12:01:28 GMT -5
Hello Mathias! Yes i know about your HX60w,mine started life as such until i found a HX60 turbine housing (brand new in box) Cheers/Stephan Höglund
|
|
|
Post by stoffe64 on Apr 18, 2024 13:58:07 GMT -5
Hello it Will be the same outer can as before, just the internal be smaller due to different reasons, time,money,difficulty level, availability to tools,machinery etc and my own health and personal life interfere with my hobbyproject, i be just happy to get it to run.....it would be a HUGE smile on my face THAT day.
|
|
|
Post by stoffe64 on Apr 18, 2024 4:28:27 GMT -5
YES it sure would be problem there, thats why i showed it ,one of problem that might occur building these engines
|
|
|
Post by stoffe64 on Apr 18, 2024 1:23:04 GMT -5
Hello ,what you see here is the inlet to my HOLSET HX60 turbine housing This would have to be portmatched with a grinder to make a smoothe transition Into the turbine Othervise it could be overtemp problems with this engine because of that disturbed flow from combustor AND it could also melt the edges of the ports and cause turbine wheel damage.
|
|
|
Post by stoffe64 on Apr 12, 2024 0:02:10 GMT -5
Hello John! If it would be the other way around, to have a too big turbine wheel you can use water injection or water/methanol injektion to compensate for the small compressor wheel.
BUT on this engine....bleed off some compressor air? But then it overtemp Again....hmmm Difficult one...it runs to some limitations but i consider this engine a achievment anyway...Good work there! Hell....my project has been on for 10 years now,still NOT built...DUUUHHH!! Cheers/Stephan
|
|
|
Post by stoffe64 on Apr 11, 2024 18:06:17 GMT -5
WOW...you have a big mismatch here my friend, your compressor wheel inducer is bigger than your turbine exducer!! THAT is bad Yeah sure, this is straight off the eBay page: Compressor: A/R 0.80 Inducer 76.6mm Exducer 102.3mm Inlet 4" Outlet 2.5" Turbine: A/R 0.96 Inducer 73.5mm Exducer 64.3mm Turbine flange T4 Outlet V band Cooled type: Oil cold Only Bearing: Floating Bearing Power : Up to 600-1000HP
|
|
|
Post by stoffe64 on Apr 11, 2024 15:23:17 GMT -5
As i have understood it ,the jetpipe outlet should be around the same diameter as the compressor wheel inducer
On my HX60 that would be 76mm,my comp wheel is 76mm inducer My turbine wheel exducer is 86mm When you put on the jetpipe on the outlet you gain more velocity and thrust
The engine becomes a turbojet, othervise without the jetpipe it is just a turbine engine! I hope you understand what i tried to explain
|
|
|
Post by stoffe64 on Apr 9, 2024 22:35:51 GMT -5
Hello John,No certainly not with liquid fuel....i be just happy to get it running this thing!
|
|
|
Post by stoffe64 on Apr 9, 2024 11:20:55 GMT -5
VERY impressive engine Andy,i am sure it will break the record!!
|
|
|
Post by stoffe64 on Apr 9, 2024 10:44:00 GMT -5
Hello guys! A decision has been made NOT to sell this turbo,at first i got so upset that my hx82 project got destroyed, i totally lost momentum,i got 60 recently also,and People started to bug me about scrap laying around at work etc etc started to clean up and i got mad,this hx60 has been laying for over 10 years This one must be built before i pass away, it Will be a VERY simple basic propane Burning turbine (to start with) I have one basic question, would this engine work with a 4" flame tube? I hope everyone is healthy here! Best regards Stephan
|
|
|
Post by stoffe64 on Mar 24, 2024 13:09:45 GMT -5
Hello all ,have this Holset HX60 turbo to sell It has a 76mm comp wheel inducer and 86mm turbine exducer with a brand new 26 housing Asking for 325 usd +shipping Best regards Stephan Höglund
|
|
|
Post by stoffe64 on Mar 11, 2024 8:54:26 GMT -5
The compressor wheel that i sell dont fit that turbo my friend, it is a hx83, titanium wheel
|
|
|
Post by stoffe64 on Mar 11, 2024 6:28:07 GMT -5
Yeah a COOL thing!
|
|
|
Post by stoffe64 on Mar 11, 2024 0:19:55 GMT -5
Hello i am selling this compressor wheel for the HX82 TURBO It has a 100 MM compressor wheel inducer,ot is brand new mambatek, never used i am looking for 200USD for it! Best regards/Stephan Höglund, sweden
|
|
|
Post by stoffe64 on Sept 25, 2023 15:23:17 GMT -5
WOW, i am VERY sad to see this,i suffer with you John....rebuild everything basicly!
|
|